AAOK

HARDWARE SET for Mounting Battery Plate to Frame Post 1936 – 1957 CHROME

HARDWARE SET for Mounting Battery Plate To Frame Post 1936 – 1957 PARKERIZED

MOUNTING PLATE (Battery) for 1936 – 1957 – replica BLACK

6 Volt BATTERY 1936 – 1964 Big Twins & 45s – H2 size (Replacement w/ Flat Post)

BATTERY COVER for 1936 – 1964 Big Twins CHROME (replica)

BATTERY POST SCREWS, NUTS & FELTS for 1923 – 1964 all models (replica)

32E 6 volt GENERATOR (less Drive Gear) 1932 – 1957 twins – NEW PRODUCTION

Special 6 volt GENERATOR (BLACK) w/ Drive Gear & built in regulator for 1932 – 1964 (use 5/16” dia. Mounting Screws)

Special 12 volt GENERATOR (CHROME) w/ Drive Gear & built in regulator for 1932 – 1969 twins (use 5/16” dia. mounting screws)

Gen. 5/16” dia. MOUNTING SCREWS for 1930 & later SV Big Twins & 45” (CHROME)

Gen. 5/16” dia. MOUNTING SCREWS for 1936 – 1969 OHV Big Twins (CHROME)

Gen. 1/4” dia. MOUNTING SCREWS for OHV 1936 – 1957 CAD

Gen. 1/4” dia. MOUNTING SCREWS for SV Big Twins 1930 – 1948 PARKERIZED

Gen. 1/4” dia. MOUNTING SCREWS for SV Big Twins 1930 – 1948 CHROME

Gen. HOLD DOWN STRAP w/ MOUNTING HARDWARE & SHIM SET for 1936 – 1957 OHV CHROME

Gen. HOLD DOWN STRAP w/ MOUNTING HARDWARE & SHIM SET for 1930 – 1957 SV CHROME

Complete GENERATOR REBUILD KIT 32E Generators 1932 – 1951

Generator DRIVE GEAR for SV 1930 – 1957

OIL DEFLECTOR for Generator Drive End

6 Volt ARMATURE for 1932 – 1957 3 Brush Generators

BRUSH SET for 32E Generators 1932 – 1951

CAGED BEARING – Gear End – 3 Brush Generators

END COVER with Screws CHROME – 1932 – 1957 Generators

GASKET – INSULATOR – SCREW Set for Main Brush Holders on 3 Brush Generators

MAIN BRUSH HOLDER – 32E Generator

BEARING SPACER .018” Thick

OUTER OIL RETAINER PLATE 1932 – 1957 Generators

SCREW Set (2) – Long for Aluminum Housing to Gen Frame

SCREW Set (4) for Pole Pieces – 3 Brush Generators

SHIM .020” Thick (pack of 5) for 3 Brush Generators

THIRD BRUSH HOLDER for 3 Brush Generators

2 Post CUT OUT RELAY for 1926 to 1937 – 6 volt electronic – BLACK Delco-Remy Cover

CABLE CLAMP for Timer Cable to Motor at Gen. Relay 1936 – 1948 OHV

3 Post CUT OUT RELAY for 1938 to 1957 – 6 volt electronic – CHROME Cover

3 Post CUT OUT RELAY for 1938 to 1957 – 12 volt electronic – CHROME Cover

Smooth COVER for 1938 – 1957 3 Post Relays – CHROME

HARDWARE Set for Mounting Plate & Cut Out Relay 1936 – 1957 OHV PARKERIZED

MOUNTING PLATE for Cut Out Relay 1936 – 1947 Knucklehead PARKERIZED

MOUNTING PLATE for Cut Out Relay 1936 – 1947 Knucklehead CHROME

HARDWARE & SPACER Set for Horn Mounting on 1936 – 1941

UPPER HORN BRACKET 1936 – 1944 BLACK

LOWER HORN BRACKET for 1942 – 1945 PARKERIZED

LOWER HORN BRACKET for 1945 – 1957 BLACK

REINFORCEMENT PLATE, Lower Horn Bracket to Fender 1936 – 1957

HARDWARE & TERMINAL SCREW Set for Horn Mounting 1942 – 1947 all twins PARKERIZED

INSULATION TERMINAL PLATE 1936 – 1941

HORN TERMINAL SCREW & POST SET 1936 – 1945 PARKERIZED

HORN BUTTON for Handlebar w/ WIRES & SCREWS 1926 up (replica) CHROME

TIMER (Circuit Breaker) Assembly for Knucklehead 1936 – 1946

TIMER (Circuit Breaker) Assembly for SV 1937 – 1946

STOP BRACKET for 1937 – 1946 SV BT

TIMER (Circuit Breaker) REBUILD KIT 1948 – 1960

ADJUSTER KIT for 1947 – 1964 all twins

GASKET for Timer Base 1937 & later Side Valves (5 pak)

TIMER COVER for 1936 – 1964 all twins CHROME

HOLD DOWN CLIP for Timer Cover 1936 – 1964 CHROME

PIVOT POST REPAIR KIT for Timer 1936 – 1947 w/ Riveting Tool

Ignition POINTS SET for 1930 – 1947

CONDENSER for 1930 – 1947

RETAINER CLIP for Timer Wire to Rear Motor Case Stud 1936 – 1969

1930 – 1947 COIL 6 volt (Chrome)

1930 – 1947 COIL 12 volt (Chrome)

1948 – 1960 COIL 6 volt (Black)

1948 – 1960 COIL 12 volt (Black)

TERMINAL BOX Assembly w/ Mounting Studs for 1948 – 1969

COIL TERMINAL SCREWS w/ PACKING NUTS & PACKING for 1930 – 1960 Ignition Coils (replica) CAD

18mm Air Cooled Champion SPARK PLUGS. New U.S. production with the old time look. Sold by the pair with Disassembly Wrench

Champion SPARK PLUG Pair w/ Copper Spacers – equivalent heat range of original #2 H-D plugs

Champion SPARK PLUG Pair w/ Copper Spacers – equivalent heat range of original #4 H-D plugs

BRASS NUT for old time Spark Plugs – 8-32 thread (sold by the pair)

ADAPTER Pair for 18mm Plug Hole to use 14mm Spark Plugs

Replica SPRINGER HEADLIGHT 6 volt “Guide” w/ Cycle Ray Logos BLACK

Replacement SPRINGER HEADLIGHT 6 volt CHROME

Headlight RIM with Screw CHROME

SPRINGS, Retainer for Headlight Lens

REFELECTOR for Headlight

BULB 12 volt for Headlight

MOUNTING BRACKET for Headlight 1936 – 1947 BLACK